View T-51750GD065J-FW-AA_449922.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

First Edition
Dec 4, 2003
LCD Module Technical Specification
Type No.
Final Revision
******
T-51750GD065J-FW-AA
Approved by (Quality Assurance Division) ) Checked by (ACI Engineering Division) ) Prepared by (Module Coordination Group)
Table of Contents
1. General Specifications.................................................................................................................................. 2 2. Electrical Specifications............................................................................................................................... 3 3. Optical Specifications ................................................................................................................................. 11 4. I/O Terminal.................................................................................................................................................... 16 5. Test................................................................................................................................................................... 18 6. Appearance Standards ............................................................................................................................... 19 7. Code System of Production Lot............................................................................................................... 18 8. Type Number.................................................................................................................................................. 22 9. Applying Precautions .................................................................................................................................. 22 10. Precautions Relating Product Handling................................................................................................ 23 11. Warranty......................................................................................................................................................... 24
Revision History
Rev. Date Page Comment
T-51750GD065J-FW-AA (AA) No. 2003-0199
OPTREX CORPORATION
Page 1/24
1.
General Specifications
Operating Temperature Storage Temperature Resolution Dot pitch Pixel arrangement Color depth Active Viewing Area Outline dimensions * : min. 0 deg. to max. 60 deg. : min. -25 deg. to max. 70 deg. : 640 x 3 [R.G.B] (W) x 480 (H) dots : 0.069 x 3 [R.G.B] (W) x 0.207 (V) mm : RGB-Stripe : 262,144 colors : 132.5 (W) x 99.4 (H) mm : 158.0 (W) x 120.36 (H) x 11.55 (D) mm * Excluding backlight cables. : 190 g typ. : Normally white-mode / Transmissive : 6:00 : 18-bit parallel data transfer (6-bit / color) : CCFL, Edge lighting type 2-tubes, replaceable * Backlight driving DC/AC inverter is not built in this module. : AGLR Coating (Low Reflectance) : Dimensional Outline UE-311848
Weight LCD type Viewing angle Interface Backlight *
Surface Treatment Drawings
T-51750GD065J-FW-AA (AA) No. 2003-0199
OPTREX CORPORATION
Page 2/24
2.
Electrical specifications
2.1. Absolute Maximum Ratings Parameter Symbol VCC VI Conditions Min. 0 0 Max. 5.5 7.0 Unit V V
Supply Voltage for LCD Logic Input Voltage 2.2. DC characteristics (1) TFT-LCD ITEM Power Supply Voltages for LCD Note A) Power Supply Currents for LCD Note B) Permissive input ripple Voltage High Low
Ambient Temperature : Ta = 25C SYMBOL VCC MIN. 3.0 4.5 ICC --VRP VIH VIL --TYP. 3.3 5.0 240 180 ----MAX. 3.6 5.5 --100 100 5.5 0.8 UNIT V V mA mA mVp-p mVp-p V V Remarks for 3.3V system for 5V system for 3.3V system for 5V system VCC=+3.3V VCC=+5.0V VCC=MAX VCC=MIN
Logic Input Voltage
2.4 0
T-51750GD065J-FW-AA (AA) No. 2003-0199
OPTREX CORPORATION
Page 3/24
[Note] A) Power and signals sequence: t1 10 ms 0 < t2 50 ms 0 < t3 50 ms 0 < t4 50 ms 500 ms < t5 VCC 3.0V or 4.5V data 0.3V 0.3V 0.3V 3.0V or 4.5V 200 ms < t6 0 t7
t1
t2 Backlight
t3
t4
t5
t6 t7 data: RGB DATA, DCLK, HD, VD, DENA
VCC-dip conditions: 1) When 2.4 V VCC < 3.0 V, td 10 ms 2) When VCC < 2.4 V VCC-dip conditions should also follow the power and signals sequence.
VCC
3.0 V or 4.5V
td
B) Typical current condition: 64- gray- bar-pattern 480 line mode VCC = +3.3 V, fH=31.5kHz, fV=60Hz, fCLK= 25MHz VCC = +5.0 V, fH=31.5kHz, fV=60Hz, fCLK= 25MHz C) For typical luminance of 400 cd/m2
T-51750GD065J-FW-AA (AA) No. 2003-0199
2.4 V
OPTREX CORPORATION
Page 4/24
2.3. AC Characteristic ITEM Frequency DCLK Period Low Width High Width DATA (R,G,B,DENA, HD, VD) Set up time Hold time Horizontal Active Time Horizontal Front Porch Horizontal Back Porch DENA Vertical Active Time Vertical Front Porch Vertical Back Porch Frequency HD Period Low Width Frequency VD Period Low Width SYMBOL fCLK tCLK tWCL tWCH tDS tDH tHA tHFP tHBP tVA tVFP tVBP fH tH tWHL fV tV tWVL MIN. 20 33.3 10 10 5 5 640 0 7 480 1 8 27 26.3 5 55 14.3 3 TYP. 25 40 ----640 --480 20 20 31.5 31.7 -60 16.7 -MAX. 30 50 ----640 --480 --38 37.0 -70 18.2 -UNIT MHz ns ns ns ns ns tCLK tCLK tCLK tH tH tH kHz E s tCLK Hz ms tH
[Note] 1) DATA is latched at fall edge of DCLK in this timing specification. 2) Polarities of HD and VD are negative in this specification. 3) DENA (Data Enable) should always be positive polarity as shown in the timing specification. 4) DCLK should appear during all invalid period, and HD should appear during invalid period of frame cycle. 5) Accepted only 640 data and 480 lines. 6) REV should be stable during operation.
T-51750GD065J-FW-AA (AA) No. 2003-0199
OPTREX CORPORATION
Page 5/24
2.4. Timing Chart
a. Pixel Timing Chart
tWCH
tCLK tWCL 0.7V CC 0.3V CC
DCLK
tDr
tDg 0.7V CC 0.3V CC
DATA(R,G,B), DENA, HD, VD
b. Horizontal Timing Chart
DCLK
First Data
DATA (R,G,B)
Invalid Data
1
2
3
639
640
Invalid Data Last Data
tHFP
tHBP
tHA
DENA
tH=1/fH tWHL
HD
c. Vertical Timing Chart
HD
LINE DATA
Invalid Data
1
2
3
479
480
Invalid Data
tVFP
tVBP
tVA
DENA
tV=1/fV tWVL
VD
T-51750GD065J-FW-AA (AA) No. 2003-0199
OPTREX CORPORATION
Page 6/24
2.5. Pixel Alignment
G B R GB R GB R G
B R GB R GB R GB R GB GB R GB R GB R GB R GB R R GB R GB R GB R GB R GB R GB R GB R GB R GB R GB GB R GB R GB R GB R GB B R GB R GB R GB R G GB R GB R GB R
T-51750GD065J-FW-AA (AA) No. 2003-0199
OPTREX CORPORATION
Page 7/24
2.6. Color Data Assignment
R DATA
COLOR
G DATA
LSB MSB G5 G4 G3 G2 G1 LSB MSB G0 B5 B4
B DATA
LSB B3 B2 B1 B0
INPUT DATA
MSB R5 R4 R3 R2 R1
R0
BLACK RED (63) GREEN (63) BASIC COLOR BLUE (63) CYAN MAGENTA YELLOW WHITE RED (0) RED (1) RED (2) RED
0 1 0 0 0 1 1 1 0 0 0
0 1 0 0 0 1 1 1 0 0 0
0 1 0 0 0 1 1 1 0 0 0
0 1 0 0 0 1 1 1 0 0 0
0 1 0 0 0 1 1 1 0 0 1
0 1 0 0 0 1 1 1 0 1 0
0 0 1 0 1 0 1 1 0 0 0
0 0 1 0 1 0 1 1 0 0 0
0 0 1 0 1 0 1 1 0 0 0
0 0 1 0 1 0 1 1 0 0 0
0 0 1 0 1 0 1 1 0 0 0
0 0 1 0 1 0 1 1 0 0 0
0 0 0 1 1 1 0 1 0 0 0
0 0 0 1 1 1 0 1 0 0 0
0 0 0 1 1 1 0 1 0 0 0
0 0 0 1 1 1 0 1 0 0 0
0 0 0 1 1 1 0 1 0 0 0
0 0 0 1 1 1 0 1 0 0 0
RED (62) RED (63) GREEN (0) GREEN (1) GREEN (2) GREEN
1 1 0 0 0
1 1 0 0 0
1 1 0 0 0
1 1 0 0 0
1 1 0 0 0
0 1 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 1
0 0 0 1 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
GREEN (62) GREEN (63) BLUE (0) BLUE (1) BLUE (2) BLUE
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
1 1 0 0 0
1 1 0 0 0
1 1 0 0 0
1 1 0 0 0
1 1 0 0 0
0 1 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 1
0 0 0 1 0
BLUE (62) BLUE (63) [Note]
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
1 1
1 1
1 1
1 1
1 1
0 1
1) Definition of gray scale Color (n) --- n indicates gray scale level. Higher n means brighter level. 2) Data 1:High, 0: Low
T-51750GD065J-FW-AA (AA) No. 2003-0199
OPTREX CORPORATION
Page 8/24
2.7. Inverted Scan Capability This module has the capability of inverting scan direction by signaling from controller. Note that scan direction cannot be changed during operation. The following figure shows the relation between the display position and the scan direction. DISPLAY POSITION Normal scan: REV = "L" D( 1, 1) D( 1, 2) | D( 1, Y) | D( 1,479) D( 1,480) D( 2, 1) D( 2, 2) | D( 2, Y) | D( 2,479) D( 2,480) ----+ --+ ----D( X, 1) D( X, 2) + D( X, Y) + D( X,479) D( X,480) ----+ --+ ----D(639, 1) D(639, 2) | D(639, Y) | D(639,479) D(639,480) D(640, 1) D(640, 2) | D(640, Y) | D(640,479) D(640,480)
Reverse scan: REV = "H" D(640,480) D(640,479) | D(640, Y) | D(640, 2) D(640, 1) D(639,480) D(639,479) | D(639, Y) | D(639, 2) D(639, 1) ----+ --+ ----D( X,480) D( X,479) + D( X, Y) + D( X, 2) D( X, 1) ----+ --+ ----D( 2,480) D( 2,479) | D( 2, Y) | D( 2, 2) D( 2, 1) D( 1,480) D( 1,479) | D( 1, Y) | D( 1, 2) D( 1, 1)
The following drawing shows the relationship between the viewing direction and the scan direction. Normal scan D(1,1) D(640,1) *@*@*@*@*@*@ Reverse scan D(1,1) D(640,1)
D(1,480)
D(640,480)
D(1,480)
D(640,480)
T-51750GD065J-FW-AA (AA) No. 2003-0199
OPTREX CORPORATION
Page 9/24
1.1. Lighting Specifications Ta=25C Parameter Lamp Voltage Lamp Current Starting Voltage Surface Luminance Average Life Symbol VL IL VS L TAL Conditions IL=6mA IL=6mA Min. 30,000 Typ. 320 6.0 4800 Max. 7.0 520 Units Vrms mArms Vrms cd/m hrs
2
Notes 1 2 3 4 5
Note 1 :The voltage ( r.m.s. ) to maintain the electric discharge of the lamp. It is measured after lighting for 3 minutes . Note 2 :The current ( r.m.s. ) to flow through the lamp with the electric discharge. It is measured after lighting for 3 minutes. Note 3 :The voltage at starting the electric discharge when the voltage is increased gradually from 0V. Note 4 :Surface Luminance is specified by the average of 9 luminance values measured at each point shown above after 20 minutes power on with the all ON pattern adjusted to maximum contrast and the dimming control of 100%. ( maximum brightness ) Note 5 : CFL Life is defined as time period that the actual luminance becomes 50% or lower of its initial value. The Average life time of CFL is defined as the time when half or more of the testing CFLs have become less bright than 50% of the initial brightness at continuous operation.
Y=60 Y=320 Y=580
P1
P2 P5 P8
P3 P6 P9
X=60 X=240 X=420
I N V VS VL
C F L
P4 P7
IL
Measurement Points
CFL Testing Circuit
Recommended Inverter : S-12645 ( Produced by ELEVAM )
T-51750GD065J-FW-AA (AA) No. 2003-0199
OPTREX CORPORATION
Page 10/24
3.
Optical Specifications
Conditions 0 0 C Standard Value Min. 300 150 0.52 0.31 0.28 0.53 0.12 0.14 0.28 0.33 0.7 10 10 10 10 Typ. 400 300 0.55 0.34 0.31 0.56 0.15 0.17 0.31 0.36 30 60 55 55 15 16 5 Max. 0.58 0.37 0.34 0.59 0.18 0.20 0.34 0.39 cd/m2 Degree Degree (Fig.5-3) Degree Degree ms ms % (Fig.5-4) (Fig.5-2) (Fig.5-1)
Method of
Remark
Item Brightness Contrast
Symbol B CR Rx Red Ry Gx Green
Unit
Measure Note5-1
Best Viewing
0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0
Color Coordinates Blue
Gy Bx By Wx White Wy
Brightness Uniformity Vertical Up
U D L R r d H
Viewing Angle Down Horizontal Viewing Angle Response Time Haze Left Right Rise Decay
Note5-1:Under the condition of maximum brightness. *Y Conditions for Measuring * Environment: Dark room with no light or close to no light. * Temperature: 255C * Humidity: 4070%RH * After backlight has been lit more then 30 minutes, driving voltage is set for optimal contrast to measure center of display. * Measure by the specified inverter or similar product. Condition: IL=6.0 mA, FL=58 kHz u Optimal viewing angle (The angle with best contrast)
6 O'clock
T-51750GD065J-FW-AA (AA) No. 2003-0199 OPTREX CORPORATION Page 11/24
(Fig.5-1) *Y Method of Brightness Measurement *iP*j Measuring Device TOPCON BM-7,Measuring Field:1 Measuring Point Center of Display =0, =0 On condition : A vertical angle from measuring direction to perpendicular. : A horizontal angle from measuring direction to perpendicular.
Center
(Pixel)
(X, Y)= (320, 240*j
LCD Module
Distance :500mm
TOPCON
BM-7
*iR*j Method of Measuring Apply signal voltage (displayed in white) to maximize brightness and measure brightness B (cd/m2). The distance between BM-7's front lens to surface panel is 500mm. Measured after backlight has been lit for more than 30 minutes. *Y Method of Contrast Measurement *iP*j Measuring Device TOPCON BM-7,Measuring Field:1 Measuring Point Center of display: same as Method of Brightness Measurement *iR*j Method of Measuring *ESet LCD module to=0, =0. *EChange signal voltage to measure maximum brightness Y1 and minimum brightness Y2. *EContrast is derived from CR=Y1/Y2.
T-51750GD065J-FW-AA (AA) No. 2003-0199
OPTREX CORPORATION
Page 12/24
(Fig.5-2) *Y Definition of Brightness Uniformity Definition is calculated from the four points (S0-S4) on the diagram below.
20mm
20mm
20mm S1 S4
S0
S2
S3 20mm
*@*@*@*@ Value of S1-S4 Minimum Standard Value of Brightness Uniformity** *@*@*@*@*@ S0
T-51750GD065J-FW-AA (AA) No. 2003-0199
OPTREX CORPORATION
Page 13/24
(Fig.5-3) *Y Method of Viewing Angle Measurement *iP*j Measuring Device TOPCON BM-7,Measuring Field:1 Measuring Point Center of display : Same as Method of Brightness Measurement *iR*j Angle of Measuring : An angle vertical to perpendicular line from the viewing direction. : An angle horizontal to perpendicular from the viewing direction.
Temperature
Rotation Table(, )
TOPCON BM-7
LCD
Computer
Control Unit & Waveform Generator
*iS*j Method of Measuring Set rotation table to =0 and set BM-7 to contrast 10 to measure angle for left and right direction of horizontal viewing angle. Also set rotation table to =90 and set BM-7 to contrast 10 to measure angle for up and down direction of vertical viewing angle .
T-51750GD065J-FW-AA (AA) No. 2003-0199
OPTREX CORPORATION
Page 14/24
(Fig.5-4) *Y Measuring Response Time *iP*j Measuring Device TOPCON BM-7,Measuring Field:1 Tektronix Digital Oscilloscope *iQ*j Measuring Point Center of display, same as Method of Brightness Measurement *iR*j Method of Measuring *ESet LCD panel to=0,and =0. *EInput whiteblackwhite to display by switching signal voltage. *EIf the luminance is 0% and 100% immediately before the change of signal voltage, then r is optical response time during the change from 90% to 10% immediately after rise of signal voltage, and d is optical response time during the change from 10% to 90% immediately after decay of signal voltage.
White
Black
White
100% 90%
Brightness
10% 0% r d
T-51750GD065J-FW-AA (AA) No. 2003-0199
OPTREX CORPORATION
Page 15/24
4.
I/O Terminal
4.1 Pin assignment
CN 1(INTERFACE SIGNAL) Used connector: DF9B-31P-1V (Hirose) Corresponding connector: DF9B-31S-1V (Hirose) Pin No. Symbol 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 GND DCLK HD VD GND R0 R1 R2 R3 R4 R5 GND G0 G1 G2 G3 G4 G5 GND B0 B1 B2 B3 B4 B5 GND DENA VCC VCC TEST REV
Function
Clock signal for sampling catch data signal Horizontal sync signal Vertical sync signal Red Red Red Red Red Red data signal(LSB) data signal data signal data signal data signal data signal(MSB) data signal(LSB) data signal data signal data signal data signal data signal(MSB)
Green Green Green Green Green Green Blue Blue Blue Blue Blue Blue
data signal(LSB) data signal data signal data signal data signal data signal(MSB)
Data enable signal(to settle the viewing area) Power Supply (DC 3.3V or 5V) Power Supply (DC 3.3V or 5V) This pin should be open. Test signal output for only internal test use. Reverse scan control. L = Normal, H = Reverse
*) The shielding case is connected with GND CN 2, CN 3 (BACKLIGHT) Backlight-side connector: BHR-02(8.0)VS-1N(JST) Inverter-side connector: SM02(8.0)B-BHS(JST) Pin No. 1 3 Symbol CTH CTL VBLH(High Voltage) VBLL(Low Voltage) Function
[Note] VBLH-VBLL = VL
T-51750GD065J-FW-AA (AA) No. 2003-0199
OPTREX CORPORATION
Page 16/24
4.2. Block Diagram
BACKLIGHT Driver(source) S1 S2 Timing I/F Connector CN1 Converter S1920
Timing signal Display data
CN2
Driver(gate)
G1 G2
Power
TFT-LCD
G480
Power Supply Circuit
BACKLIGHT
CN3
BACKLIGHT CCFL CN2,CN3 1 3
T-51750GD065J-FW-AA (AA) No. 2003-0199
OPTREX CORPORATION
Page 17/24
5.
Test
No change on display and in operation under the following test condition.
Conditions:
Unless otherwise specified, tests will be conducted under the following condition. Temperature: 205C Humidity : 655%RH tests will be not conducted under functioning state. Parameter Conditions 60C, 96hrs (operation state) 0C, 96hrs (operation state) 70C, 96hrs -25C, 96hrs 40C,90~95%RH, 96hrs Frequency:10-57Hz/Vibration width(one side):0.075mm :58-500Hz/Gravity:9.8m/s Sweep time:11minutes Test period:3hrs for each direction of X,Y,Z
2
No. 1 2 3 4 5 6
Notes
High Temperature Operating Low Temperature Operating High Temperature Storage Low Temperature Storage Damp Proof Test Vibration Test
1 2 1,2 1,2 3
7
Shock
Shock level:490m/s2 Waveform:half sinusoidal wave, 11ms Number of shocks : One shock input in each direction of three mutually perpendicular axis for a total of six shock inputs
8
Shock Test
To be measured after dropping from 60cm high on the concrete surface in packing state.
Dropping method corner dropping F E B 60cm Concrete Surface G D A C A corner : once Edge dropping B,C,D edge : once Face dropping E,F,G face : once
Note 1: No dew condensation to be observed. Note 2: The function test shall be conducted after 4 hours storage at the normal Temperature and humidity after removed from the test chamber. Note 3: Vibration test will be conducted to the product itself without putting it in a container.
T-51750GD065J-FW-AA (AA) No. 2003-0199
OPTREX CORPORATION
Page 18/24
6.
Appearance Standards
6.1.Inspection conditions The LCD shall be inspected under 40W white fluorescent light. The distance between the eyes and the sample shall be more than 30cm. All directions for inspecting the sample should be within 45against perpendicular line.
45
6.2.Definition of applicable Zones
X
X
X
A Zone B Zone X C Zone X : Maximum Seal Line
A Zone : Active display area B Zone : Out of active display area up to viewing area C Zone : Rest parts A Zone + B Zone = Viewing area
T-51750GD065J-FW-AA (AA) No. 2003-0199
OPTREX CORPORATION
Page 19/24
7.
Code System of Production Lot
The production lot of module is specified as follows.
Factory Control Number (0~9) Date of the week (A~G) Factory Number (0~9) Factory Code (Alphabet) Production Week (1~5) Production Month (1~9, X, Y, Z) Production Year (Lower 2 digits)
8.
Type Number
The type number of module is specified as follows. T-51750GD065J-FW-AA
9.
Applying Precautions
Please contact us when questions and/or new problems not specified in this Specifications arise.
T-51750GD065J-FW-AA (AA) No. 2003-0199
OPTREX CORPORATION
Page 22/24
10. Precautions Relating Product Handling
The Following precautions will guide you in handling our product correctly. 1) Liquid crystal display devices 1. The liquid crystal display device panel used in the liquid crystal display module is made of plate glass. Avoid any strong mechanical shock. Should the glass break handle it with care. 2. The polarizer adhering to the surface of the LCD is made of a soft material. Guard against scratching it. 2) Care of the liquid crystal display module against static electricity discharge. 1. When working with the module, be sure to ground your body and any electrical equipment you may be using. We strongly recommend the use of anti static mats ( made of rubber ), to protect work tables against the hazards of electrical shock. 2. Avoid the use of work clothing made of synthetic fibers. We recommend cotton clothing or other conductivity-treated fibers. 3. Slowly and carefully remove the protective film from the LCD module, since this operation can generate static electricity. 3) When the LCD module alone must be stored for long periods of time: 1. Protect the modules from high temperature and humidity. 2. Keep the modules out of direct sunlight or direct exposure to ultraviolet rays. 3. Protect the modules from excessive external forces. 4) Use the module with a power supply that is equipped with an overcurrent protector circuit,since the module is not provided with this protective feature. 5) Do not ingest the LCD fluid itself should it leak out of a damaged LCD module. Should hands or clothing come in contact with LCD fluid, wash immediately with soap. 6) Conductivity is not guaranteed for models that use metal holders where solder connections between the metal holder and the PCB are not used. Please contact us to discuss appropriate ways to assure conductivity. 7) For models which use CFL: 1. High voltage of 1000V or greater is applied to the CFL cable connector area. Care should be taken not to touch connection areas to avoid burns. 2. Protect CFL cables from rubbing against the unit and thus causing the wire jacket to become worn. 3. The use of CFLs for extended periods of time at low temperatures will significantly shorten their service life. 8) For models which use touch panels: 1. Do not stack up modules since they can be damaged by components on neighboring modules. 2. Do not place heavy objects on top of the product. This could cause glass breakage. 9) For models which use COG,TAB,or COF: 1. The mechanical strength of the product is low since the IC chip faces out unprotected from the rear. Be sure to protect the rear of the IC chip from external forces. 2. Given the fact that the rear of the IC chip is left exposed, in order to protect the unit from electrical damage, avoid installation configurations in which the rear of the IC chip runs the risk of making any electrical contact.
T-51750GD065J-FW-AA (AA) No. 2003-0199
OPTREX CORPORATION
Page 23/24
10) Models which use flexible cable, heat seal, or TAB: 1. In order to maintain reliability, do not touch or hold by the connector area. 2. Avoid any bending, pulling, or other excessive force, which can result in brokenconnections. 11) have an adverse effect on connecting parts ( LCD panel-TCP / HEAT SEAL / FPC / etc., PCB-TCP / HEAT SEAL / FPC etc., TCP-HEAT SEAL, TCP-FPC, HEAT SEAL-FPC,etc.,) depending on its materials.Please check and evaluate these materials carefully before use. 12) In case of acrylic plate is attached to front side of LCD panel, cloudiness ( very small cracks ) can occur on acrylic plate, being influenced by some components generated from polarizer film. Please check and evaluate those acrylic materials carefully before use.
11. Warranty
This product has been manufactured to your company's specifications as a part for use in your company's general electronic products. It is guaranteed to perform according to delivery specifications. For any other use apart from general electronic equipment, we cannot take responsibility if the product is used in medical devices, nuclear power control equipment, aerospace equipment, fire and security systems, or any other applications in which there is a direct risk to human life and where extremely high levels of reliability are required. If the product is to be used in any of the above applications, we will need to enter into a separate product liability agreement. 1. We cannot accept responsibility for any defect, which may arise from additional manufacturing of the product (including disassembly and reassembly), after product delivery. 2. We cannot accept responsibility for any defect, which may arise after the application of strong external force to the product. 3. We cannot accept responsibility for any defect, which may arise due to the application of static electricity after the product has passed your company's acceptance inspection procedures. 4. When the product is in CFL models, CFL service life and brightness will vary According to the performance of the inverter used, leaks, etc. We cannot accept responsibility for product performance, reliability, or defect, which may arise. 5. We cannot accept responsibility for intellectual property of a third party, which may arise through the application of our product to your assembly with exception to those issues relating directly to the structure or method of manufacturing of our product. 6. Optrex will not be held responsible for any quality guarantee issue for defect products judged as Optrex-origin longer than 2 (two) years from Optrex production or 1(one) year from Optrex, Optrex America, Optrex Europe delivery which ever comes later.
T-51750GD065J-FW-AA (AA) No. 2003-0199
OPTREX CORPORATION
Page 24/24

▲Up To Search▲

Price & Availability of T-51750GD065J-FW-AA

	To Download T-51750GD065J-FW-AA Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .